• Up next:Manufacturing process planning for CNC milling

Pre-test

Before you begin this course, test your skills by taking the following assessment to see where you stand. 

Keep track of your incorrect answers to know which skills you should study. You'll have a chance to take this same practice test again at the end of the course to see how you've improved.

All questions must be answered to submit your assessment.

Pre-test

53 questions

1. Refer to exhibit.

Which command should be used to round a sharp corner on a body shown in the before/after image?

Error: Select an answer

2. Which right-click option should be used to remove a component from an assembly without maintaining its feature history?

Error: Select an answer

3. A CNC programmer is tasked to program the same part that has multiple material types. The programmer will create material presets for each tool. Using a machinability rating of materials chart, which single function requires modifying for each material type?

Error: Select an answer

4. Which tool can modify the radius of a fillet, increase the diameter of a hole, and change the extruded thickness on a body?

Error: Select an answer

5. A typical 3-axis vertical CNC mill has the spindle positioned directly above the part.

Which direction must the table be jogged in order to bring the machined part closer to the operator?

Error: Select an answer

6. Refer to exhibit.

What must be selected to enable the Part Position tab when creating a new setup for Milling?

Error: Select an answer

7. Refer to exhibit.

A CNC programmer is creating a 2D Contour toolpath using a chamfer mill on the edge shown in the exhibit.How is the chamfer width defined to exactly match the model?

Error: Select an answer

8. Refer to exhibit.

What is the most common toolpath to efficiently remove all material in the red area as noted by the arrow?

Error: Select an answer

9. How can a tool in the samples library be modified?

Error: Select an answer

10. Which surface command requires a closed loop selection?

Error: Select an answer

11. A CNC programmer is using the drill cycle to feed to depth and immediately retract at the same feedrate once reaching the final depth.

Which drill cycle is chosen?

Error: Select an answer

12. The CNC programmer has selected 2D adaptive to rough machine mold cavities. The file size for this strategy is too large for the control memory. To reduce the file size, the programmer should modify which Passes option?

Error: Select an answer

13. Refer to exhibit.

A CNC programmer is creating a facing toolpath on the part shown in the exhibit.What does the highlighted orange edge represent?

Error: Select an answer

14. Refer to exhibit.

What geometry is automatically selected when creating a face operation as shown in the exhibit?

Error: Select an answer

15. Refer to exhibit.

In the exhibit which parameter defines the total depth a tool can be used before contacting the non-cutting portion?

Error: Select an answer

16. Which two selections are valid for the creation of a new sketch? (Choose two.)

Select 2 answers below.
Error: Select 2 answers

17. Refer to exhibit.

A CNC programmer is using a roughing toolpath to remove material from the part shown in the exhibit.

The large pocket is 1.1" deep and the tool used has a flute height of 0.75".

Which toolpath setting should be enabled?

Error: Select 2 answers

18. What is the most important reason to accurately locate digital workholding and stock in 3D?

Error: Select 2 answers

19. Refer to exhibit.A CNC programmer has been given a 3D model of a brake caliper to be prototyped.

The CNC programmer has used Minimum Radius Analysis as seen in the exhibit to determine tool sizes required for finishing details.

What corner radius bull nose endmill should the CNC programmer select?

Error: Select 2 answers

20. Which option should be used to rotate the camera view normal to the active sketch plane?

Error: Select 2 answers

21. Manufacturer's fixtures can be found in the Data Panel under Samples.

The fixtures are found in which Fusion 360 sample project?

Error: Select 2 answers

22. A CNC programmer has created a roughing pass on a pocket with stock to leave set at 0.1 inch.When creating a 2D Contour toolpath to finish the pocket, which option should be enabled to prevent excessive radial tool loading?

Error: Select 2 answers

23. Which joint type allows for only 1 degree of translation applied to components that are designed in place?

Error: Select 2 answers

24. Refer to exhibits.


A CNC programmer imported a vise assembly that included joints to allow the vise's sliding jaw to move. The vise assembly was set up to hold a part to be machined.The CNC programmer accidentally moved the vise jaw back as seen in exhibit 2. How can the jaw be placed back in its location in exhibit 1?

Error: Select 2 answers

25. While using the right-hand rule, you align your right thumb to the X positive direction of the machine, which axis direction does your index finger point?

Error: Select 2 answers

26. Refer to exhibit.

The body shown has an opening that must be covered to prevent a tool from dropping into it during roughing.Which surface feature should be used?

Error: Select 2 answers

27. Refer to exhibit.

Based on the toolpath simulation options in Fusion 360, what will occur?

Error: Select 2 answers

28. Refer to exhibit.

A CNC programmer is setting up a drilling operation for the part shown in the exhibit.Which drilling order was used?