# Schematic Basics Part 1: Search, Place, Move

February 24, 2017 10 min read

# How to Search, Place, and Move Your Symbols in Autodesk EAGLE

You’ve got all the right ideas, but do you know what to do with them? Schematic design is needed to get those ideas out of your head and into action! Schematic symbols from the foundation of every electronics design, and if you’re like most engineers, then you probably started doodling your circuit on the back of a napkin or your notebook. Now that you’ve got all that circuitry on paper, it’s time to put it into practice in your PCB design tool.

## A Few Disclaimers

There are a few things we’d like to cover before we journey further, specifically:

It’s good to have a general understanding of all the parts that you can place on a schematic and their appearance. We’d recommend saving this handy reference list, or even printing out the chart below and hanging it above your desk.

Why? First, this will be a huge help if you ever need to review any schematic. And second, there’s a ton of symbols, many of which look different depending on if you’re looking at a US or international schematic. It’s near impossible to remember all of those, so keep this chart handy.

Some of the most common symbols you’ll find used in electronic schematics.

### Creating a Schematic Is a Multi-Step Process

Next, let’s talk about the process that it takes to complete a schematic for a PCB. Selecting and placing your symbols is just one piece to the puzzle. To give you an idea of what it takes to consider a schematic fully complete, here are all the steps:

1. First, you need to find, place and orient all of your symbols on a blank schematic sheet. That’s what this blog post is all about.
2. Next, you need to provide some electrical connectivity between each part with nets and assign values and names to your parts. This will be covered in Part 2.
3. And lastly, you need to make sure everything is connected as it should be by running an ERC, or Electrical Rule Check. This will be covered in Part 3.

Let’s start working with schematic symbols!

## Step 1 – Creating Your First Project and Schematic

We’re going to assume that this is your first time working with Autodesk EAGLE. Download EAGLE for free if you do not have it already. Every project is organized into a project folder, with schematics, PCB layouts, and other files all nestled together in one location. This makes it easy to keep things organized. Let’s create your first project and add a brand new schematic with these steps:

1. First, open Autodesk EAGLE, and you’ll be greeted with the Control Panel. This is your home away from home and will contain all of your libraries, projects, scripts, and more.
2. From the Control Panel, select File » New » Project and give your new project folder a name.
3. Next, right-click on your project folder and select New » Schematic to add a new schematic sheet to your project.
4. This will open a blank schematic document. Before you do anything else, save your schematic by selecting File » Save As and give it a name.

Now we have our project folder set up with our first schematic. If you go back to your Control Panel you’ll be able to see all of your project files organized together as shown below:

Our first project folder and schematic highlighted in orange. There’s also a ton of example projects that are included in Autodesk EAGLE for free.

## Step 2 – Activating Your Libraries

Next, you’ll need to activate all of the libraries that come with EAGLE, and there’s a ton of them! This is one of the remarkable benefits of using EAGLE, as most of the parts you need for your design have already been created by someone else, so you don’t have to spend time making them yourself.

To begin, select the Add icon  on the left-hand side of your EAGLE schematic. This will open the ADD Dialog, notice that it is blank.

None of the libraries are showing up that come with Autodesk EAGLE. The solution – they need to be activated first.

By default, when you open EAGLE for the first time none of the default libraries will be activated. So let’s go back to your Control Panel and turn them all on with these steps:

1. In your Control Panel, select the arrow next to the Libraries folder. You can see we have a ton of libraries to add, but there’s an easy way to make this happen.
2. To add all of your libraries at once, right-click the Libraries folder, then select Use All.
3. If there are any libraries you want to activate or deactivate individually, simply right-click a library, and select Use.

As you can see in the image below, all of the part libraries in our Libraries folder have a green dot next to them. This means that they’re activated and ready for use in our schematic.

The green dots indicate that a library is active and ready for use.

You might have noticed that there are other sub-folders within the main Libraries folder from elektro, element14, etc. These sub-folders didn’t get activated from the steps you did above since the libraries are nested within another folder. But no worries, if you want to activate these libraries just repeat the steps above for each individual folder.

You’ve got your libraries activated now, let’s start searching for and placing your symbols.

## Step 3 – Searching and Placing Your Schematic Symbols

Let’s find our first part, a timer, with these steps:

1. In the Search field, type in “NE555” and press enter. This should bring up one search result from st-microelectronics – NE555 General purpose Bipolar Timer. You’ll notice that this part has its own preview that shows off its symbol, footprint, description, and attributes.

Here’s an NE555 timer, notice how every part includes a symbol, footprint, description, and set of attributes.

2. Using this part in your schematic design is simple. To do this, select the part name, then select the OK button to enter into placement mode on your schematic.
3. Next, left-click anywhere on your schematic sheet to place your symbol. Let’s go ahead and place 3 of these timers so we can practice our deleting skills later.
4. Once you’re done placing your symbol, press the Escape key to get out of placement mode, which will open the ADD Dialog again.

You just placed your first schematic symbol. Easy enough, right? You can repeat the process above to add all of the parts you need for your schematic. There are a few more parts to add, so head back into the ADD panel and search for the following parts:

• Resistors – You’ll need 4 of these. Search for “resistor” and choose the first one in the resistor > R-US_ folder.
• LEDs – You’ll need 2 of these. Search for “LED5mm” which should be the only option that shows up in your search.
• CapacitorYou’ll need 1 of these. Search for “electrolytic capacitor” and choose the first one in the rcl > EL- folder.
• Connector – You’ll need 1 of these. Search for “M02” which should be the only Amp Quick Connector that shows up in your search.

If you were following along, then your schematic sheet should have the parts shown below (where they are placed doesn’t matter, right now):

All the schematic symbols you should have so far, we’ve got (4) resistors, (2) LEDs, (1) capacitor, (1) connector, and (3) bipolar timers.

## Step 4 – Moving, Deleting and Rotating Your Parts

Alright, now that you have all of your parts placed, it’s time to learn how to delete all of those extra timers you added earlier. Then we’ll get your parts facing the right direction with some rotation options, and then we can move every symbol to its proper location!

### Deleting Parts

You have three timers sitting on your schematic sheet, but you only need one. Let’s learn how to delete those extra ones with these steps:

1. Select the  Delete icon  on the left-hand side of your interface.
2. You’re now in delete mode, and all you have to do now is select the middle of each timer symbol to delete them.
3. Delete a part on accident? Just select Edit » Undo to bring it back to life. Or, press CMD + Z on Mac or Ctrl + Z on Windows.

We’re now down 2 timers, leaving us only the essential parts we need for this circuit.

### Rotating Parts

Now that you have all of those unnecessary parts deleted, let’s get everything facing the right direct direction with these steps:

1. Select the Rotate icon  on the left-hand side of your interface.
2. Next, left-click once on a resistor. This will rotate it 90 degrees. Left-click again to rotate it 180 degrees, and so on. Rotate all of your resistors 90 degrees, so they’re all vertical.

All of your other parts should already be in their correct rotation, but if not, make sure everything matches up with our schematic below:

Now that all of our parts are in the correct orientation we can be moved to where they need to be.

### Moving Parts

Now, let’s get everything moved into place on your schematic. This part is important as your symbols need to be placed in the way they will be wired on your completed schematic. Follow these steps:

1. Select the Move icon on the left-hand side of your interface. This icon looks like a set of 4 arrows, all facing in their respective North, East, South, and West directions.
2. Next, left-click one of your symbols. This will highlight it in a bright red color, indicating that it’s now actively selected and ready to be moved.
3. You can now drag this symbol around on your schematic sheet wherever you please. When you’re ready to confirm the new placement, left-click again to place the part.

This process is pretty straightforward. Go ahead and move all of your parts around to make it match our schematic below:

Our schematic with all the symbols in their place, ready for wiring with nets.

## Interface Alternatives

There’s one handy alternative that we’d like to point out about the EAGLE interface before we send you on your way. In the steps above, you relied on the set of icons on the left-hand side of your interface to perform all of your actions. However, this isn’t the only way to get things done; there’s also the right-click Context Menu, check it out:

The right-click context menu provides a ton of options when working with symbols.

You can open this context menu by hovering over a symbol with your mouse or trackpad and right-click. You’ll notice that many of the actions we used today can be found in this menu. Keep the Context Menu in mind the next time you need to adjust your symbols. The choice is yours.

## First Steps Accomplished

You did it! Your schematic symbols are now placed and ready to be wired, which we’ll be covering in our next blog. This is a big first step in your EAGLE journey. Here’s a quick recap of what you learned today:

Projects – First, you learned how to create a new project and schematic sheet in Autodesk EAGLE. This all went down in the trusty Control Panel.

Parts – Next, you activated your libraries and learned how to search for parts in the ADD panel, then you placed them on your schematic.

Placement – Lastly, you learned how to get rid of all those unnecessary symbols with the delete option and then you rotated and moved your parts to their new home.

This is a great first start, but it’s just the beginning of your schematic. Here’s what you can look forward to in the rest of the Schematic Basics series for Autodesk EAGLE:

• Schematic Basics Part 2 – Schematic Wiring & Values – Learn how to wire all of your schematic symbols together with nets and how to add values and part names.
• Schematic Basics Part 3 – Checking Connectivity with ERC – Learn how to confirm that you’ve wired everything together on your schematic correctly with an ERC, or Electrical Rule Check.

Making your first schematic in the free version of Autodesk EAGLE is just the tip of the iceberg!

Get the full experience today and upgrade now to Autodesk EAGLE Subscription.